6x19M= 6x(1+6+12) IWRC/ÇÖ

HALAT SİPARİŞİ

 

VERİLEN SİPARİŞLERİNİZDE SİZE DAHA İYİ HİZMET VEREBİLMEMİZ VE HER TÜRLÜ YANLIŞ ANLAŞILMAYI ÖNLEMEK İÇİN SİPARİŞ FORMUNUZDA AŞAĞIDAKİ MADDELERİ LÜTFEN TARAFIMIZA BİLDİRİNİZ.

1.HALAT ÇAPI (-/+ TOLERANS)

2.HALAT UZUNLUĞU (-/+ TOLERANS)

3.HALAT YAPISI (KOMPOZİSYONU)

4.HALATIN TEORİK/MİNİMUM KOPMA YÜKÜ

5.HALAT VE TORON SARIM YÖNÜ

6.KAPLAMA ŞEKLİ (GALVENİZLİ VEYA SİYAH)

7.YAĞLAMA ŞEKLİ

8.PAKETLEME ŞEKLİ

9.TERMİN SÜRESİ

10.SEVK ADRESİ
 

---

HALATIN TANIMI

TELLERİN ÇEŞİTLİ KOMPOZİSYONLARA GÖRE ÖRÜLMESİYLE MEYDANA GELMİŞ EN AZ 4 ADET DAMARIN BİR ÖZ TARAFINA (P.P.C, SISAL, ÇELİK) HELİSEL OLARAK SARILMASIYLA İMAL EDİLEN BİR ÜRÜNDÜR.




 

---

HALAT YÖNÜ

HALATIN SARIM YÖNÜ OLARAK GENEL MANADA İKİYE AYRILIR. ÇAPRAZ HALATLAR VE DÜZ HALATLAR.

 

---

ÇAPRAZ SARIMLI HALATLAR

HALAT YÖNÜ İLE DAMAR YÖNÜ BİRBİRİNİN TERSİ YÖNÜNDE SARIMLI HALATLARDIR. SAĞ ÇAPRAZ VE SOL ÇAPRAZ OLMAK ÜZERE İKİYE AYRILIRLAR. SAĞ ÇAPRAZ HALATLAR "s/Z", SOL ÇAPRAZ HALATLAR "z/S" OLARAK YAPILANIRLAR. 

 

---

DÜZ SARIMLI HALATLAR 

DAMAR VE HALAT YÖNÜ BİRBİRİNİN AYNI YÖNÜNDE SARIMLI HALATLARDIR.  SAĞ DÜZ SOL DÜZ SARIMLI HALATLAR OLMAK ÜZERE  İKİYE AYRILIRLAR. SAĞ DÜZ HALATLAR "z/Z", SOL DÜZ HALATLAR "s/S"  OLARAK YAPILANIRLAR.

 

---

HALAT ÇAPININ ÖLÇÜLMESİ

.

1.DIAMETER OF RAPE (-/+ TOLERANCES)

2.WIRE RAPE LENGTH (-/+ TOLERANCES)

3.CONSTRUCTION OF WIRE RAPE

4.CONSTRUCTION OF WIRE RAPE

5.ADDITIONAL BREAKING LOAD / MINIMUM BREAKING LOAD

6.TYPE OF LAYING

7.KIND OF LUBRICANT

8.PACKING

9.DELIVERY TERMS

10.DELIVERY ADDRESS
 

---

THE DEFINITION OF THE WIRE ROPE 

THE WIRE ROPE IS MADE UP WRAPPING  AT LEAST 4 STRANDS AROUND CORE WHICH IS MADE P.P.C, STEEL, FIBER. EVERY STRANDS AND STELLS WRAPPED LIKE HELIX IN A DIFFERENT COMPOSITION.




 

---

LAY OF WIRE ROPE

IN GENERAL MEANING: THE WIRE ROPE LAID IN TWO MANNERS, REGULAR LAY AND LANGLAY WIRE ROPE.

 

---

REGULAR LAY WIRE ROPE

THE DIRECTION OF THE WIRE LAY IN THE STRAND IS OPPOSITE TO THE DIRECTION  OF THE LAY IN THE ROPE. IT IS TWO KIND; RIGHT REGULAR LAY "s/Z", LEFT REGULAR LAY "z/S" THESE  ARE CONSTRUCTED LIKE BELOW SHAPES.


 

---

LANG LAY WIRE ROPE

BOTH STRAND LAY AND ROPE LAY ARE IN THE SAME DIRECTION. THERE ARE TWO TYPES; RİGHT LANG LAY "z/Z" AND LEFT LANG LAY "s/S" CONSTRUCTED.




 

---

MEASURING THE WIRE ROPE

IN ORDER TO MEASURE THE DIAMETER OF THE STEEL WIRE RAPES, THE FOLLOWING CERTAIN INSTRUCTIONS SHOULD BE FOLLOWED; FIRST A SAMPLE OF WIRE ROPE IS HOLDED STRAIGHT AND WITHOUT ANY LOAD EXERTED ON IT SECOND, IT SHOULD BE BEGIN AT LEAST. 
1.5 MT FROM THE END, WHİLE MEASURING THE DIAMETER  OF THE RAPE. THIRD, TWO MEASUREMENTS  ARE DONE 1,5 MT INTERVALS FROM THE TWO POINTS. EVERY MEASUREMENTS POINT SHOULD BE VERTICAL TO EACH OTHER. LAST, REAL DIAMETER OF THE STEEL WIRE ROPES IS DEFINED AS THE AVERAGE OF THESE FOUR MEASUREMENTS.



 

---

HOW TO CUT ROPE

THE TWO SİDES WİLL BE CUT ROPE SOFT POINT WITH ONE OR CLAMP WIRE CUTTING İS PERFORMED CLİNGİNG.